Clik here to view.
PTO CLUTCH JOHN DEERE 300 Problems
:bye:Hello my name is Gaines, I have a John Deere 300 lawn mower with a kohler engine K341 and the new PTO that was sent to me wasn't even close to lining up.! Can anyone try and help I ordered a new...
View ArticleClik here to view.
Took Some Pictures Around the Yard Today
I took a camera out to try & catch some Yellow Swallowtails that were around this afternoon, of course they left! So I just took some pics of the gardens instead: HPIM3115.JPG HPIM3116.JPG...
View ArticleOpinions on engine block heater
I'll be playing with my new 1023e come sometime next week. I talked to the dealer today about installing a block heater, he said it really wasn't necessary. I'm a little unsure, but I trust the man,...
View ArticleHello from the green mountian state!
I live in Vermont as you can tell and have visited your site many times looking for answers to my questions about my tractor chioces. I have purchased a John Deere 5105M cab to replace my 5520 Os. It...
View ArticleFluid in rear tires or not?
They tell me my new 5045E came in today. I am wrestling with the idea of putting fluid in the rear tires or not. Also, if I do, what would you put in? He said something about beet juice or water with...
View ArticleBlack Grim looking stuff on Engine
If I run my JD 115 Automatic for a day like 5 hours+ Theres this black grim that starts to form on the engine block. Is this from the exaust? Should I be concerned? Are there ways to prevent it?...
View ArticleHas anyone here successfully killed large areas of Bermuda grass?
I won't mind the Bermuda grass in my yard if it wasn't so invasive, but it is so I want to be rid of it. I should have attacked the problem a long time ago before it got out of hand. I've been doing a...
View ArticleInstalling a 47" quick hitch blower onto 1025r
Can anyone send info on part numbers needed to install a 47" quick hitch snowblower from a x595 to a 1025r. I know the shaft from the blower needs to be replaced, need a new shaft from mid pto, and a...
View ArticleClik here to view.
4x10 Series Fault Codes
These fault codes cover the 4210, 4310, and 4410 Tractors-others may be similar but I cannot verify at this time. One covers the eHydro (HST) models, and the other is for the ePowerReverser (EPR)...
View ArticleClik here to view.
Joun Deere & Company USA Loactions
I found this on my PC from years ago, it details all the USA locations for JD USA. Attached Files uslocations.pdf (1.18 MB)
View ArticleD140 issues
Hello all. I am new to the forums and have been browsing/looking to see if my issue has already been answered. To start I am not the most mechanically inclined with engines; however, I think I may have...
View ArticleClik here to view.
Tire Rubbing Hydaulic Hose
Yesterday while performing a general inspection my 1025R, I picked up on an impending significant problem. The left front tire was rubbing the hydraulic hose for the power steering...see pics. When...
View Article1025r Exhaust
I finally managed to get the 1 1/4" chrome drain fitting over the factory exhaust pipe. On this one and the 1026r always had the angle pointed to the ground . Today while loading 25 or 30 trailer loads...
View ArticleClik here to view.
A use for the Model A
My son Nick has been driving his Model A all over the farm and that was about all he was doing with it. The other day he was digging around in a bunch of junk, er stuff, in an old corn crib and found...
View ArticleClik here to view.
Raising back of seat on 1025r
Here are a few photos of factory hex bolt and bolt installed top of my bolt had 8.8 on head if any help. Grandson used a 1/2" wrench to tighten the bolt In first photo you can see the front factory hex...
View ArticleClik here to view.
Gave my 1023e it's first real workout today.....
Tried out the Howse rotary cutter today at our camp in Greene Co. Pa.. The terrain is very hilly with lots of little hidden surprises on the ground lol! Dad just sold his 8n so now I'm using my...
View Article1025R Can't put into Lock position ?
Hey all . I've had my scut for a couple of weeks now and through this forum , have gone through the deck adjustments to level the cut height . But for some reason I can't (not even when new) get the...
View ArticleSleep Number beds
Do you own one? If so, do you like it and is it worth the money you paid for it? They're really expensive, but if they alleviate back pain and allow good sleep, they may be worth it. Warranted for 25...
View Articlenew member
Hello all going to try to restore a 2040 that my Dad started yrs ago, he decided that it was not what he wanted to do with his time and gave it to me, been sitting out back for 4 yrs, my Dad turned 77...
View ArticleChanging 1025r Mechical Lift to Hydraulic
I want to change my mechanical lift to the hydraulic for the MMM on my 1025r. I found in JD literature that I need 2 parts kits, LVB26205 and LVB26206 to do this. I assume they will come with...
View Article