318 Charging problem
Hello All: I've got a 318 built in 1985 w/ a B43G motor with a charging light problem. I've read several other posts and did some of the trouble shooting, and here's where I'm at. Cleaned all grounds...
View ArticleNostalgic video
Take the trip,...it's a nostalgic coupla' minutes! ENJOY! :-) -- https://www.youtube.com/v/J55S38xwxnQ
View Article100 Series Lawn Tractor have shear pin interlocked with ignition?
I have a 100 Series lawn tractor and recently broke one of the blades. I replaced the blades but engine doesn't want to turn over. Is there a shear pin or re-set switch or safety interlock with the...
View ArticleAbout to finalize 2032r purchase, then 2720 and 3320 options appeared. Please...
Went to my dealer this afternoon to go over the final numbers, for apples to apples comparison I will only list the price for the tractors and the FEL. 2032r with H130 loader: $19400, at dealer, H130...
View Article1025r mower deck adjustment
Like a number of posters my 1025r maximum cutting height seems low, lower than my old JD185, for example. I note that when the deck is raised fully (either in rear PTO only or mid and rear PTO...
View Article300 CX curl cylinders bit the big one.
I have a 2010 3720 with 300cx FEL with 400 hours on it. The curl cylinders allow the curl to drop almost all the way down in about 1-2 seconds. I ordered 2 cylinder repair kits hoping installing them...
View Article1023e weight with loader?
I have a 1023e I need to transport and need the weight with loader. If I remember correctly the bare tractor was just over 1300 lbs. I guess the MMM deck at 150 but have no idea of the loader weight....
View ArticleBucket Capacities and Sizes for 300CX loader
Does anyone have the information regarding the different bucket sizes and cacpacities for the 300CX loaders for the 3 series tractors? I have checked my local Deere delaer and they are struggling to...
View ArticleIndependent lift for midmount mower on a 4320
Does anyone have an independent lift for a 72" mid mount mower on a 4320? I have a 2013 4320 with a 485 backhoe. I would like to be able to drop the backhoe and use the mower without removing the sub...
View Article1st time Deere owner!
Just bought a 2000 JD 455 and couldn't be happier about my purchase. Looking to get a blade or blower and tiller for it.
View ArticleHello from Pittsburgh
Hello All I am in the waiting stage of receiving my new JD. I went with a 1025R FILB (TLB) with the 60" 7-Iron Auto Connect Deck. Just ordered Kens Weld on Hooks&Clevis. I have been watching the...
View Article430 Radiator Hose Replacements
I have previously replaced all of my large diameter radiator hoses on my 430 several years ago when all the hoses were available from John Deere. I want to again replace them as I have noticed these...
View ArticleAdjustable top link for 3-pt
So in anticipation of getting my new tractor I've been watching videos of how to use some of the implements. Specifically the box-blade. It seems like an adjustable top-link is required so that you can...
View ArticleCat 0 3 pt hitch for a 445
What's the best route to get one of these? Buy straight from Deere (and pay out the wazoo)? Keep creeping on Craigslist? Or is there an aftermarket brand out there that's worth purchasing? Thanks in...
View ArticleJohn Deere 1026R Rock Shaft
The rock shaft lever is not riding on the mower deck height adjustment cam on my 1026 R. Any help would be appreciated .
View ArticleJD 216 smokes when first started
I'm going to look at a JD 216 Saturday and the owner says it smokes on start up but not after that . Should I be concerned, is this a sign of bigger troubles? I just don't want to get stuck with...
View ArticleLX277 mower help
I have an LX277 that has a short some where. The battery draws down very quickly overnight after a fresh charge. I have tried troubleshooting the issue with a multimeter with no luck. I thought it was...
View ArticleUnknown noises
I have been hearing extra noises when mowing and I trying to find? I noticed 2 bolts rattling when engine in idle? I identified them as 2 bolts missing flange nuts # 14M7303 from the bottom of flywheel...
View ArticleHello from Harrisburg
Hello to all Was talking to my local dealer today about a possible new "toy" in the future and he told me about Green tractor talk, gotta say i dont own a tractor :( but i do own a d125, Gx85, and...
View ArticleClik here to view.
Hello from WV
I purchased an X585 a couple of weeks ago but haven't been able to mow because of the rain, maybe next week. IMG_0155.JPG Attached Images IMG_0155.JPG (135.6 KB)
View Article