Is it possible to use a hydraulic splitter on a 2032r for deck/fel?
I find that I am hating having to get off and switch the hoses so I can run the bucket on the tractor while the MMM is mounted. Does anyone know if there is some kind of 2 into 4...
View ArticleClik here to view.
Flywheel Removal
I have an oil leak behind the flywheel and I am trying to take it off. As you can see, I got the bolts and locking nuts off but when I try to pull off the wheel it hits something and wont come off. I...
View ArticleCurl leak on John Deere 4410
The curl function on my JD 4410 with 430 loader leaks down. The corresponding function on the rear implement also leaks down. Is there anything that can be done short a new spool valve?
View ArticleConverting an old 4x2 Gator to electric...
I'm trying to convert an old gas 4x2 gator to electric drive. I'm debating how to connect the motor to the transmission. I could do it any one of 3 ways: 1. Remove the secondary clutch and use a chain...
View ArticleJohn Deere LX178 blows fuse when using mower
I inherited an older LX178. Been fixing on it. Installed mower deck after cleaning and grease job. Totally dead. Replace PTO switch. Mower runs, but only for a minute. Then blows 15A fuse. What else...
View Article1982 1050 Starter/ Solenoid Problems
I'm having a bit of a strange problem with my JD 1050. The first time I crank her up each day she starts fine, no problem. However, after several hours of use, if I turn it off to take a break or...
View ArticleP218G RPM's increase as engine gets hotter
Anybody know what causes a Onan P218G to have RPM's increase after it mows for 30+ minutes? Once it gets good and warm I have to move down the throttle to keep it from over-revving. I modified the...
View ArticleLX178 Carburetor surging problem
I inherited an LX178 that has been sitting around for a few years with gas in the tank, hoses, etc. I cleaned out the tank, blew out the lines and installed a new fuel filter. Put in fresh fuel. I got...
View ArticleGreat experience with Mutton during recent purchase
Just wanted to say how pleased I was with my recent (and first) Mutton experience. I ordered a Frontier landscape rake on a Tuesday, Shane shipped it out on Wednesday and the truck stopped at my...
View ArticleMX-6 Cut Quality
I have had an MX-6 Rotary cutter for the last 7 years and even when it was brand new I have never gotten a very good cut on my fields and I alway overlap my cuts to try and get what the tractor tires...
View Article2007 4120 and 4720 Engine Differences?
Shortly after I got my tractor the salesman at the Deere dealership was telling me if I wanted more power that they could turn up the injection pump and pto dyno my tractor to get the power level up to...
View ArticleNew Guy from KY
Hello everyone. Bought a 1025r last month. Got the h120 loader and 60d deck. Enjoying my seat time. Brent
View ArticleQA on 160D loader vs. 305 loader
All- Help! Another newbie question. Looking at attachments for my 160d loader. My salesman's out today or I would ask him. Do implements that fit the 305 loader quick tach fit the 160D loader? Or are...
View Article5420 Tilt Steering Problem
I have a 5420 and my tilt steering won't lock. My steering wheel just moves up and down. Any suggestions would be greatly appreciated. Bill
View Article4720 Filter/Separator leaking
Found a continuous flow draining from the filter/separator on the 4720 today like I had loosened the screw to drain the water but the screw was tight. JD Parts list a valve kit RE60854 and a seal kit...
View ArticleClik here to view.
JB weld and my LT155
My LT155 is almost 15 years old and has been used very much over that time. The splined pulley that goes on the input shaft of the hydrostatic transmission is worn allowing the pulley to wobble and...
View ArticleClik here to view.
Bumble bees, bushhogging and, thankfully, a tractor with a cab
I ran over a bumble bee nest today while bushhogging my field. I stopped counting at 2 & 1/2 million bees :wink: well maybe not that many but several dozen were greatly agitated because I had mowed...
View Articlehydraulic power low?
I was using my 750 tractor today and I could not raise the front wheels off the ground with the FEL. There usually has been a sweet spot in the control where I could lift the front end 2 feet off the...
View Article