My new printers
Well, not mine, they belong to the company. :) So, if you haven't seen it in other posts, what I do for fun during the day revolves around digital print. Today was a particularly special day. 2 of our...
View ArticleClik here to view.
Hydraulic problem with a German Model 830 from 1974
I purchased an 830 at auction 3 months ago. It was working well until a line coming from the front hydraulic pump started leaking recently. I replaced the lines going to and coming from the pump. Since...
View ArticleRiveting Lug Brackets to Blank Rear Rim
On my LA, I have one rim 8"x24"which is rusted out but still have the tire on it and holding air. I have a new blank rim and a set of lug brackets to make me a new rim for my LA. Everything is measured...
View ArticleBunch of 1/32 4 wd for sale
I have a big lot of 1/32 4wd for sale almost all are collector Steiger series/ big buds and a few ours 26 plus total plus some 1/64 ih Woud love to sell as one lot make offer have pics all but 2 new in...
View ArticleLoader use
How do you guys feel about using the tip of the bucket on a 1026r loader to push non running vehicles into the shop?
View ArticleClik here to view.
Another Ballast Thread...
There has been a lot of threads and posts about rear ballast. This is what I made up with about $10 in on hand material, including the bungy cord. It pins quick and easy to the top link pin. My tractor...
View ArticleSolenoid Valve Project
I need a little help with a hydraulic problem. I want to use my Hydraulic Power Beyond to run two valves, for two cylinders on each side of a pull behind box blade. So first, is it true that to control...
View ArticleHow much play would you expect on JD quick attach?
My new grapple is very loose at the JDQA pins. It appears they drilled the clevis pin holes too far out. The result is a greater than normal clunking. It does seem to help clear dirt from the roots but...
View ArticleSun Shade
Does anyone have a sun shade on their 2720/2520 tractor? I am considering one from these folks: John Deere canopies Thanks, Roger
View ArticleClik here to view.
Vietnam War remnant
Spotted this while taking a little road trip on July 4th. Amazing how it was shot down and sent to Texas for repairs then back to Vietnam for more action. Too bad they didn't erect some sort of...
View Article2305 jd won't start
Just used it last week. When it cranks it's like almost running, but when I let go of the key it dies. Have replaced fuel filter, has oil, has new gas, air cleaner good. Could it be fuel pump or dirty...
View Article1941 Deere LA Flat Belt Pulley and Shaft Installation
I am rebuilding a Quill housing/shaft to be able to use a flat belt pulley on my 1941 LA. The portion that fits inside the motor has a square opening that look like it may be for oil to run into. Is...
View ArticleClik here to view.
Mower Deck Suspension - - - 62D1 Deck for 2520 & 2720
Those of you familiar with the 62D1 deck will recognize the pictures below. They show one side of the lift link assembly that enables adjustment of the 62D1 deck to insure a level cut. While mowing...
View ArticleLX188- Loose or worn drive belt
Hello. I have a JD LX188. While I was mowing the other day- my mower would no longer go forward or reverse. The peddles would not even move. Then the tractor started smoking so I immediately shut it...
View ArticleNew guy patiently waiting 1025r
I've been moving just under 2 acres the past 5-years with a snapper lt200 and an older wh /toro 268h. I'm a bagger and have been lugging around a trakvac with two 40 gal rubbermaid cans. In the spring...
View ArticleLikelihood of getting an autoconnect "dud"
So as you guys know from the other thread, my 1025R should be here within 5-7 days. I have the 60" Deck with autoconnect on order. However, I've read about all kinds of problems with getting it to...
View Article54D MMM on 2320R lift knob question
Hello, I am a new tractor owner. Our 2320R was delivered yesterday. We did not order the independent lift (hydraulic) as the dealer said it had a mechanical lock to separate it from the 3PTH when using...
View Article2520 MFWD engagement lever
Maybe this thread will need to be merged with the "popping out of 4WD" thread, but for now, I have a question. My 2520 still occasionally pops out of 4WD. I have been conducting several experiments,...
View ArticleDrain lines for AC in sound guard cab
I am restoring a '81 4040 Here is my problem now. I replaced the drain lines for the AC with 1/2" air line but did not put a trap in the line. You know the little loop that at the end of the line. Does...
View ArticleClik here to view.
Finally Forks!
I just picking up these forks from the dealer. Their Frontier 48" and adjustable. Can't wait to get out and give them a try. I'm guessing the list of uses for these are very long. They work good for...
View Article