Horizontal Scroll Bar
A horizontal scroll bar is showing up on/in all post any ideas as to why?
View ArticleClik here to view.
Replacing steering components on my L118
So first off, I will address the underlying issue I was having with my L118. Plain and simple, it was hard to steer. However with 404 hours on it, I can understand why the major steering components...
View ArticleClik here to view.
New 1025R
I picked up my new 1025R at the dealer Tuesday. I had to order it to get the turf tires. I also ordered the 54D Autoconnect Deck with mulching kit. The deck came with the optional hydraulic lift kit...
View ArticleClik here to view.
Is this normal for a loader??
Ever since I took delivery of my 3320 I noticed that my loader arms were a little off. When I say a little off I mean that the loader arms ends aren't equally balanced. It didn't bother me much at...
View ArticleClik here to view.
When a Missourian Redneck Meets a Welder
I saw this today, so I had to stop. IMG_0183.JPG The JD rims are welded to the car rims. No engine, but someone must had one of those moments where he thought he had an idea.... While there I looked at...
View ArticleClik here to view.
My John Deere 1907 -1910 wagon
Still some work to do but it's close. Attached Images P6153655.JPG (747.7 KB) P6153656.JPG (740.8 KB) P6153657.JPG (741.8 KB)
View Article318 mule drive/belt tension
ok, here's whats up.. I put a new belt on my 318 (from pto to mower deck) and have had a heck of a time with it jumping off the pulleys after about 10mins of mowing.. The last time it jumped, it got...
View Article260 backhoe issue
Good morning friends, I hate to make some of you put down your coffee to answer my question but I'm in need of help. I just purchased the 260 backhoe for my 1026 and it now has around 5 hrs. on the...
View Article1025(6)r wheel weights
Hi everyone: Does anybody know how far out three wheel weights extend beyond the sidewall of the tires? For the H120 loader, the manual calls for one of three options: 1. Wheel weights (three each...
View ArticleJohn Deere 4020 electrical issue...
I was brush hogging the other day and the Deere quit on me. I had been at it for about an hour and had to hop off real quick so i killed the pto, took the throttle to idle and about 10sec later it...
View Article2520 bucket floppy when back dragging
Hey guys, I just noticed that the bucket has gotten sloppy or has that floppy bucket thing when back dragging. The tilt cylinders are actually compressing and I can even make them compress by hand if I...
View Article2210 and 62C MMM attachment kit and installation questions
I just recently purchased a 62C MMM for my (new to me) 2210. My tractor only came w/ the FEL, and I needed a deck to mow with so I happened upon one on craigslist. Problem is, I'm not sure if I have...
View ArticleClik here to view.
Building pallet forks
Well, I finally got going on my pallet fork project. The main frame is 4x2x1/4" tube, 48" long. The reinforcements at the upper hook and 4" wide, 3/8" angle. The upper hooks are 1.5". 2.jpg 4.jpg 6.jpg...
View ArticleClik here to view.
2008 JD 2520 for sale, Virginia
126 hours, still using occasionally. - 200CX loader - LX5 rotary mower (clutch, not shear pin) - R4 tires - also comes with tooth bar for loader and 3-pt. rear blade - clean, very light use residential...
View Article4440 shifting problems
When the tractor is cold or warm will shift up to the high side meaning 2 or 4 but after it is run hard it won't pull in 2 or 4 but pulls fine in 1 or 3 on a b c or d .
View ArticleJohn Deere 8440
Can a 6081A motor be used to repower a John Deere 8440 which has a 6/466a motor installed.
View ArticleNo Grease Fittings on Pivot Pin and Tie Rod?
So I've had my 1026r for a few months and just was looking over the tractor more and noticed there are no grease fittings on the tie rod or the front axle pivot pin.. Anyone been creative and added...
View Article318 engine/wiring diagram
Good morning folks and a belated happy father's day to all the JD guys who are dads out there. I've been pulling apart the 89 318 with the Onan P218G engine to recondition everything and I have the...
View Article2305 Big Problem
Hi Everyone, I have a 2305, I managed to hit a rock half buried in the ground, the damage is horrible. I went back to the garage, and tranny fluid was coming out. the collard on the deck that attaches...
View Article1 Series 50hr Service (Gasket Material Found)
Hi All, Just completed my 50hr service on my 1026R and found gasket material in the drain pan and stuck to the suction screen when draining the transmission oil. I brought the material in to show the...
View Article